Amano CP-5000 Manual de Operações

CP-5000 Electronic Time Recorder User’s Guide

2-2 CP-5000 User’s Guide Front Cover Removal The front cover must be removed to connect the Full Power Reserve Battery and connect the external sign

CP-5000 User’s Guide 2-3 Placement/Location When choosing a mounting location for your CP-5000, you should ensure the following parameters are met:

2-4 CP-5000 User’s Guide Wall Mounting For proper wall mounting, follow these steps: 1. Disconnect the power cord from the power source. 2. Unl

CP-5000 User’s Guide 2-5 11. Carefully pivot the CP-5000 away from you onto the back plate until its side hooks fit in the slots on the back of the

2-6 CP-5000 User’s Guide External Signal Connections The CP-5000 is equipped with a single external signal relay circuit that enables you to activa

CP-5000 User’s Guide 2-7 3. Strip approximately .25” (6 mm) of insulation off the ends of the wires that will be connected to the CP-5000. 4. Rem

2-8 CP-5000 User’s Guide Optional Accessory Battery Pack (ATR-20095x) Installing the Full Power Reserve Battery (available as a kit: P/N ATR-20095x)

CP-5000 User’s Guide 2-9 Note: The battery will not power the clock until after the clock is initially plugged in. Afterwards, power will automatic

2-10 CP-5000 User’s Guide Initialization and Reset Prior to first use, the CP-5000 must be initialized to clear any possible unexpected program pa

CP-5000 User’s Guide 2-11 Initialize your CP-5000 as follows: 1. Remove the top cover. Set the Mode Switch to Program/Ink Mode. 2. Insert a smal

Proprietary Notice This document contains proprietary information and such information may not be reproduced in whole or part without the writte

2-12 CP-5000 User’s Guide This page intentionally left blank.

CP-5000 User’s Guide 3-1 Chapter 3: Time Cards Making a Test Print Follow these steps to make a test print: 1. Make sure that there is power to th

3-2 CP-5000 User’s Guide This page intentionally left blank.

CP-5000 User’s Guide 4-1 Chapter 4: Programming Introduction The CP-5000 must be programmed before use. There are two types of programming: Basic a

4-2 CP-5000 User’s Guide Entering and Saving Values Values are changed in each programming menu item by pressing the Change key. Holding down the C

CP-5000 User’s Guide 4-3 Programming Guide The following is a reference guide for programming the CP-5000: Indicator Menu/ Item Description Displa

4-4 CP-5000 User’s Guide Indicator Menu/ Item Description Display Accepted Values 41 Hour Display (page 4-12) 1: 24-hour format 2: 12-hour forma

CP-5000 User’s Guide 4-5 Indicator Menu/ Item Description Display Accepted Values 51 Signal Duration (page 4-14) 1 -15: Signal Duration (seconds

4-6 CP-5000 User’s Guide Basic Programming Programming Password (Menu 3) Note: As supplied, the CP-5000 is configured with the default password “00

CP-5000 User’s Guide 4-7 2. Press the Change key until the correct two digit year (00 thru 50) is flashing in the display. Holding down the Change

CP-5000 User’s Guide i Table of Contents Chapter 1: Introduction...1-1 Specif

4-8 CP-5000 User’s Guide Hours and Minutes (Menu 1, Item 3) Note: To set the hours and minutes, you must cycle through the following sequence of d

CP-5000 User’s Guide 4-9 7. The hour and minutes entered will flash in the display. To edit these settings, press the Change key. This will return

4-10 CP-5000 User’s Guide • Menu 2, Item 2 Sets the DST start date’s month and date. • Menu 2, Item 3 Sets the DST end date’s month and date. Note

CP-5000 User’s Guide 4-11 6. Select the Enter key, and now the date value flashes. Select the Change key until the correct date appears for the st

4-12 CP-5000 User’s Guide Hours Display and Imprint (Menu 4, Items 1 – 7) This group of menu items is used to set the time format (12 or 24 hour) o

CP-5000 User’s Guide 4-13 8. Using the Change key, select one of the following: Accepted Values Imprint 0 Off 1 Day of Week (1 to 7) 2 Day of W

4-14 CP-5000 User’s Guide 15. When the desired value appears, press the Enter key. When saved, the next menu item, Index No. Imprint, will appear in

CP-5000 User’s Guide 4-15 Weekly Programming (Items 01 – 80) This menu allows you to create a weekly schedule that will enable or disable certain f

4-16 CP-5000 User’s Guide Creating a Weekly Program Note: To create a program or schedule, you must cycle through the sequence of displays of each

CP-5000 User’s Guide 4-17 Note: The duration (1 to 15 seconds) that the Buzzer will be ON for is set in the Signal Duration menu (page 4-14). 7. P

ii CP-5000 User’s Guide Obtaining a Printout of Programmed Data (Menu 7)...4-18 Editing Weekly Programs ...

4-18 CP-5000 User’s Guide Obtaining a Printout of Programmed Data (Menu 7) 1. If you have not already done so, enter the Program Mode and press th

CP-5000 User’s Guide 4-19 There are no programmed events for programs two and three (STP 2 or STP 3). 6. To stop printing at any time, press and ho

4-20 CP-5000 User’s Guide Deleting a Weekly Program Note: Weekly Program number 1 can not be deleted. 1. Obtain a printout of the current Weekly

CP-5000 User’s Guide 5-1 Chapter 5: Maintenance Service With the exception of the ribbon and the time/date memory backup battery, there are no user-

5-2 CP-5000 User’s Guide 4. Insert a new ribbon between the ribbon guide and the printer head. 5. Press the ribbon down until it clicks into pla

CP-5000 User’s Guide 5-3 Time/Date Memory Backup Battery Amano recommends the replacement of this battery every five years. The battery maintains th

5-4 CP-5000 User’s Guide 7. Plug the power cord into the AC outlet. 8. Reprogram the date and time. Note: If the Full Power Reserve Battery optio

CP-5000 User’s Guide 6-1 Chapter 6: Troubleshooting Introduction If your CP-5000 should fail to operate properly, you should perform the following

6-2 CP-5000 User’s Guide • Run the Signal Test from the Diagnostics menu to check if the Signal relay is operating properly. If it is not, contact

CP-5000 User’s Guide 6-3 Error Messages There are nine possible error messages (Err 1 thru Err 9) that can appear in the display. When one of the

CP-5000 User’s Guide 1-1 Chapter 1: Introduction Before attempting to use the Amano CP-5000 time recorder/stamp, please carefully review Chapter 1:

6-4 CP-5000 User’s Guide • The slider on the printer carriage is not moving correctly due to a missing black plastic bushing in the small holes on

CP-5000 User’s Guide 6-5 • The block sensor is malfunctioning. If this condition persists, contact your local Amano dealer. Card not in Clock Thi

6-6 CP-5000 User’s Guide Timing Sensor Error This error occurs when a card gets stuck or irregular card motion is detected by the card transport me

CP-5000 User’s Guide 6-7 Display Related Problems Low Battery If the accessory battery is installed and operating the clock during a power failure

6-8 CP-5000 User’s Guide Hour Change If the time displayed is off by an hour (either up or down), one of the following may have occurred: • The p

CP-5000 User’s Guide 6-9 Card Refused, Date and Time in Display If a time card is inserted into the card throat, refused, and a beep sounds, the ti

6-10 CP-5000 User’s Guide Wrong Color Printed The CP-5000 has the ability to print in red or black ink. When the top cover is installed (Normal Mod

CP-5000 User’s Guide 6-11 Diagnostics (Menu 8) The Diagnostics Menu is used to run specific diagnostic routines for troubleshooting and determining

6-12 CP-5000 User’s Guide Mode and Keys Test (Menu 8, Item 2) 1. If you have not already done so, enter the Program Mode and press the Function key

CP-5000 User’s Guide 6-13 LCD Test (Menu 8, Item 3) 1. If you have not already done so, enter the Program Mode and press the Function key until th

1-2 CP-5000 User’s Guide Accessories The following accessories are provided with the Amano CP-5000. After unpacking, please ensure that all of the

6-14 CP-5000 User’s Guide 4. Press the Enter key to stop the test. A beep will sound and the test number will flash in the display. 5. Press the Cha

CP-5000 User’s Guide 6-15 Signal Test (Menu 8, Item 6) 1. If you have not already done so, enter the Program Mode and press the Function key until

6-16 CP-5000 User’s Guide Firmware Version Number (Menu 8, Item 8) 1. If you have not already done so, enter the Program Mode and press the Functio

CP-5000 User’s Guide 7-1 Chapter 7: Appendix The following blank chart is provided to assist you in creating Weekly Programs for your CP-5000. Prog

7-2 CP-5000 User’s Guide Program No. Moment Object Days Time 1. Buzzer 2. Signal 3. Color 1 2 3 4 5 6 7 HH:MM0: Off 1: On 0: Off 1: On 0: N

CP-5000 User’s Guide 7-3 Program No. Moment Object Days Time 1. Buzzer 2. Signal 3. Color 1 2 3 4567HH:MM0: Off 1: On 0: Off 1: On 0: No Ch

7-4 CP-5000 User’s Guide This page intentionally left blank.

ATR-105904A • Copyright © 2009 Amano Cincinnati, Inc. • 04/09/0 Corporate Headquarters 140 Harrison Avenue, Roseland, NJ 07068-1239 (800)

CP-5000 User’s Guide 1-3 Names and Functions of Parts The following describes the names and functions of various parts of the CP-5000. External View

1-4 CP-5000 User’s Guide Component Name Normal Mode Program/Ink Mode LED Indicator Day of the week Current menu in display Mode Switch Norm

CP-5000 User’s Guide 2-1 Chapter 2: Getting Started Before using the Amano CP-5000 time recorder/stamp, please carefully review this chapter of the